Page 120 - catalgo33

HeIGHt GAGe AccessorIes

252 HeIGHt trAnsfer GAGes AccurAcy And lonG-lIfe feAtures
0-48"/0-1200MM • Extreme rigidity provides the vibration-proof stability
necessary to permit precise repeat readings with
The 252 Height Transfer Gage is ideal for use with test indicators or electronic indicators of the highest amplification
amplifiers to accurately transfer height settings from gage blocks, height gages
and other standards. • Extremely rigid, rectangular box-type hollow column
mounted integrally on a heavy base
• Adjusting mechanism is located in the base so the
252 Height Transfer Gages
column and indicator are isolated and not affected by
HeigHt gages Cat. No. EDP Range (Approximate) (Approximate) Gage Rod Dimension eAse-of-operAtIon feAtures
Fine Adjustment Base Size - L x W
external factors, such as heat or hand pressure
0-14"
5-3/4" x 3-1/2"
252Z-14 55890
(350mm)
(145 x 90mm)
• Hand-fitting base design for sure-grip handling and
0-24"
7-1/2" x 4-1/2"
9" L x .375" Dia. (225 x
easy movement
3/8" (9.5mm)
252Z-24 51216
(600mm)
0-48"
9" x 6"
252Z-48 51217
(1200mm) (190 x 115mm) 9.5mm) with steps • Bottom of the base has three ground and lapped pads
(225 x 150mm)
for stability and smooth movement on the surface plate
Larger sizes available on special order.
Starrett 708, 709, 711, 650 Test Indicators; 25, 81, 196, 655, 656 Dial Indicators and supplementary attachments • Adjustable slide, incorporating a snug for holding test
also available. indicators or electronic gage heads, has rapid vertical
Gage furnished with 9" (225mm) Rod and PT06784-A Gage Holding Rod in wood case.
manual adjustment
• Thumb screw allows slide to be locked
• Knob on base allows fine vertical adjustment of the
slide unit relative to the fixed column. This permits the
slide with its test indicator to be quickly and precisely
adjusted to the desired setting.
tool And GAGInG Holders
• A snug on the slide provides two holes (.375" [9.5mm]
and .156" [4mm]) for holding gage rods or scribers. A
9" (225mm) rod furnished with the gage is especially
useful for reaching confined areas or reaching heights
greater than the range of the gage.
• The rod has a major diameter of .375" (9.5mm) and
stepped diameters of 1/4" (3.2mm) and 7/32" (5.5mm)
at one end and 5/16" (8mm) at the opposite end
• 708 and 709 Test Indicators can be mounted on this
rod using PT22428 swivel clamp. 196 Universal Back-
Plunger Indicators can be mounted using Starrett snugs,
Part PT18718 or PT18724 (snugs not furnished).
• PT06784-A Gage Holding Rod is included to
accommodate the 715-1 Gaging Head when the
Transfer Gage is used with the 717 Electronic Gage. A
wire retaining clip keeps electronic gage head cables
from deflecting the gage-holding rod.
• 25, 81, 655 and 656 Dial Indicators also can be used
on the height gage by means of a PT06784-A Gage
Rod (furnished)
• Other useful attachments (extra) are surface gage
spindles (57C or 57D, 12" [300m]) and 18" [450mm])
– which are extremely useful for scribing and layout

Pictured with 717 Gage Amplifier
and 715-12 lever probe.

120